stm32f103c8t6 Microcontroller

A microcontroller is an integrated circuit device. It uses a microprocessor unit (MPU), memory, and peripheral to control other portions of an electronic system. It is a small, low-cost, and self-contained computer-on-a-chip used as an embedded system. A few microcontrollers may utilize four-bit expressions and work at clock rate frequencies,z little measure of RAM, programmable ROM, and flash memory, parallel and serial I/O, timers and signal generators, digital to analog, and analog to digital conversion. Microcontrollers usually must have low-power requirements since many devices they control are battery-operated. The dominant part of microcontrollers being used nowadays is implanted in other apparatus.

In stm32f103c8t6,theSTM32means ARM-based 32-bit microcontroller, F indicates general purpose usage, 103 is the performance line,  C shows the number of pins (C=48 pins), 8 is the Kbytes of Flash memory ( 8 = 64), T indicates the package type ( T = LQFP), and 6 is the operating temperature ( 6 = Industrial temperature range, –40 to 85 °C)

 

The stm32f103c8t6incorporates an ARM® 32-bit Cortex®-M3 CPU Core capable of operating at 72 MHz maximum frequency and can perform Single-cycle multiplication hardware division. The stm32f103c8t6has 64 or 128 Kbytes of Flash memory and 20 Kbytes of Static random-access memory (SRAM). The stm32f103c8t6has a built-in clock, reset and supply management system. It has a 2.0 to 3.6 V application supply and I/O, a 4-to-16 MHz crystal oscillator, an internal 8 MHz factory-trimmed RC and a 32 kHz oscillator for RTC with calibration. The stm32f103c8t6switches between Sleep, Stop, and Standby, and it has a VBAT supply for RTC and backup registers. The stm32f103c8t6offers 2 x 12-bit, one µs A/D converters (up to 16 channels) with a Conversion range of 0 to 3.6 V and a Temperature sensor. The stm32f103c8t6has aseven-channel DMA controller and supports Peripherals such as timers, ADC, SPIs, I 2Cs, and USARTs. Up to 80 fast I/O ports are all mappable on 16 external interrupt vectors and almost all 5 V-tolerant. The stm32f103c8t6has a serial wire debug mode(SWD) and JTAG interfaces. It also has three 16-bit timers, two watchdog timers, a SysTick timer 24-bit down counter, and a 16-bit motor control PWM timer with deadtime generation and emergency stop. The stm32f103c8t6supports up to 9 communication interfaces which include 2 x I2C interfaces, 3 USARTs, 2 SPIs (18 Mbit/s), CAN interface (2.0B Active) and a USB 2.0 full-speed interface.The stm32f103c8t6operates from a 2.0 to 3.6 V power supply. They are available in both the –40 to +85 °C temperature range and the –40 to +105 °C extended temperature range. The stm32f103c8t6is used in the design of low-power applications due to its comprehensive set of power-saving modes.

 

These features make the stm32f103c8t6medium-density performance microcontroller suitable for a wide range of applications such as motor drives, application control, medical and handheld equipment, PC and gaming peripherals, GPS platforms, industrial applications, PLCs, inverters, printers, scanners, alarm systems, video intercoms, and HVACs.

 

Comments

Post a Comment

Popular posts from this blog

TL1963AQKTTRQ1

Image
  The TL1963AQKTTRQ is a low-dropout (LDO) regulator that is designed for the fast transient response. With a dropout voltage of 340 mV, the device can deliver 1.5 A of output current. The operating quiescent current is 1 mA, and in shutdown, it drops to less than 1 mA. The output voltage ranges between 1.21 and 20 volts. Quiescent current is well-controlled; unlike many other regulators, it does not rise in dropout.The TL1963AQKTTRQ regulators feature a low output noise and fast transient response, making them excellent for sensitive RF supply applications. With output capacitors as low as 10 F, the TL1963AQKTTRQ regulators are stable. Small ceramic mlcc capacitors can be employed instead of ESR, as is the case with most other regulators. In TL1963AQKTTRQ voltage regulators, reverse-battery protection, current limiting, heat limiting, and reverse-current protection are all built into the internal protection circuitry.Fixed output voltages of 1.5 V, 1.8 V, 2.5 V, and 3.3 V are availab
Read more

XC6SLX16-3CPG196C (FPGA)

Image
  FPGAs are semiconductor devices that are built together around the matrix of configurable logic blocks (CLBs) coupled using programmable interconnects. Following production, FPGAs can indeed be reprogrammed to meet specific industry or feature requirements. FPGA technology is gaining momentum in a variety of industries, including aerospace and military, automotive, consumer devices, high-performance data and networking processing, multimedia and image processing, wired and wireless communications. Different manufacturer companies are operating in the world. Xilinx, Inc. (WE); Intel Corporation (US); Lattice Semiconductor Corporation (US); Microchip Technology Inc. (US); and Quick Logic Corporation are the top contenders in the FPGA industry (US).XC6SLX16-3CPG196C is FPGA by the Spartan 6 family launched by Xilinx. The main features of this module are, Logic optimized FPGAs that requires low cost for designing. The performance parameter analysis reveals that the module XC6SLX16-3
Read more

SN65HVD485EDGKR (transceiver)

Image
  A transceiver is a transmitter/receiver that exists in a single box. Whereas the phrase is most commonly associated with wireless communications equipment, it can also refer to transmitter/receiver devices in cable or optical fiber networks. This electrical device's primary function is to broadcast and receive various signals. The transceiver in radio communications can operate in half-duplex or full-duplex mode: half-duplex transceivers It can transmit or receive data, but not at the same instant. This is because the sender and receiver are linked to the same antenna through an electrical switch. This method is commonly used in ham radios, walkie-talkies, as well as other single-frequency Full-duplex transceivers. The radio transmitter and receiver can operate in tandem. Various radio frequencies are used for transmission and receiving. This mode may be found in both portable and cellular two-way radios. Full duplex is more efficient but the significance of both networks is de
Read more